TITAN V2 NGRS BASIC [Rear Wired] Controller
Set

Drop-In Mosfet type
TITAN™ controller set transforms Tokyo Marui V2 Next Generation Recoil Shock
into an advanced training replica. It provides a tactical advantage thanks to a
lightning-fast trigger reaction time with the ability to modify the replica and
adapt it to every mission with the help of 20 available functions.

Modules in BASIC version have following
features:

– AUG mode
– diagnostics function
– firmware updates
– cycle detection
– trigger sensitivity adjustment

ATTENTION! In order to unlock all functions of ADVANCED version,
it is necessary to purchase FIRMWARE UPGRADE for ADVANCED version
on www.gatee.eu/editions website.

TITAN™ provides new possibilities:
– Trigger sensitivity adjustment
– Pre-cocking boost – adjustment of the time that the spring is being kept
pulled (shortens the time between a squeeze of the trigger and firing)
– Adjustment of fire mode selector modes
– Burst mode
– Fire rate adjustment
– Notifies about a low battery level
– Protects battery from damage
– “Sniper delay”

More comprehensive description of TITAN™
controller:

TRIGGER SENSITIVITY ADJUSTMENT
III generation proximity sensor allows controlling the trigger sensitivity.
There is no need to disassemble the replica, all that is necessary is to use
the GATE™ control station. It will allow adapting the replica to the skills and
individual preferences of the User.

CONFIGURABLE FIRE MODE SELECTOR (GEN. 2)
Two sensors can be programmed in three ways to select one of 6 functions:
– SAFE-SEMI-AUTO
– SAFE-SEMI-SEMI
– SAFE-SEMI-BURST*
– SAFE-BURST*-AUTO
– SAFE-SEMI-BURST*/AUTO (short squeeze-and-hold – BURST, long trigger
squeeze-and-hold AUTO)
– SAFE-BURST*-AUTO (SAFE via a rapid mode selection, when: SAFE-SEMI-SAFE)
*BURST means firing a series of rounds.

CYCLE DETECTION
TITAN™ control unit can accurately detect the position that a cycle should end
at. Thanks to that, the squeeze of a trigger causes a completion of a full
firing cycle (replicas without TITAN™ system often jam when the trigger has
been squeezed for a too short of a time if it does not end with a
shot. TITAN™ eliminates this defect.).
This results in:
– Automatic BURST mode, there is no need to set the time of the cycle of this
series, the only thing necessary is to determine how many BBs are to be fired
– Automatic Pre-Cocking, which is available in every mode in the following fire
mode selector settings: SEMI BURST and AUTO. In comparison to ordinary MOSFET
modules, there is no need to configure this setting manually. All that is
required is to set the power of the spring pre-cocking.
– ALWAYS COMPLETED FULL CYCLE – when pre-cocking is turned-off, TITAN™ will
ensure that the gearbox will complete a full cycle and after firing the spring
will be released. Thanks to this, a greater reliability of the replica is
achieved.

PRE-COCKING (Gen.2*)
Winning a duel often depends on fractions of a second, that is why thanks to
pre-cocking the trigger reacts with a speed that can be compared to that of a
real firearm. The spring is pulled beforehand, so at the same time, we caution
that usage of this mode with powerful springs will lead to a faster wear of
internal parts of a replica.
There are two modes of PRE-COCKING function:
1. AUTO – the spring is pulled after every shot
2. SMART – the spring is pulled in advance by a slow squeeze of the trigger and
a shot is fired by a rapid squeeze.
Three modes of operation can programmed for
PRE-COCKING: HIGH / MID / LOW – each regulates the spring sprain in different
levels

*PRE-COCKING mode operates now in all fire
mode selector modes: SEMI, BURST, AUTO and does not require manual calibration

BURST (Gen.2)
BURST mode, i.e. firing with a pre-programmed series
of rounds requires only the selection of the amount of BBs to be fired (up to
10 BBs per trigger squeeze). It is very useful in all MILSIMs or when using
real/low-cap magazines.

ROF CONTROL
This allows to reduce the rate of fire of the replica. This allows to use more
powerful Li-Po batteries and still maintain a rate of fire compliant with real
firearms.

ROF STAB
Allows to change the way ROF CONTROL operates:
– ON – RoF Control regulates the cycle speed, which
allows a gearbox to operate smoothly and with a lesser wear of the replica’s
internal parts
– OFF – RoF control adds pauses between every shot in
order to reduce the rate of fire. This provides very realistic experience.

SNIPER DELAY
This function allows to set a delay between every shot in SEMI mode in order to
simulate reload delay or recoil compensation. It is possible to set the following
delay: 0.5 s, 1.0 s, 2.0 s and 3.0 s.

A detailed
description of all functions is available on the manufacturer’s website:
http://www.gatee.eu/

The full manual is available at the below address:

https://gatee.eu/pl/produkty/titan/ttn-v2-ngrs-pl

The set includes:

– TITAN module with BASIC software
– assembly kit
– User’s manual
– GATE collector’s patch

ATTENTION!  In order to configure TITAN system, it is
necessary to use USB-Link or Tactical Programming Card that are not included in
the set and need to be purchased separately.